Thursday, May 08, 2014

Half of Half Done

One of four trucks put together.


Parts made for one of two cars.

Lessons learned.  When drilling the hole for the axle do not center on the imprecise bandsaw cut, center it on the precise drilled bolt hole.  To get the axles parallel and the wheels in line with each I had to reach back to my Red X days of measuring and trial and error.  I got everything good on the third try because I had figured out what what red x and pink x were and how to stack the odds in my favor.

Wednesday, May 07, 2014

Bent Arches

Today continued building of the trucks.  I started by finishing one side frame to make sure it would work.  Other than needing to open the holes in the bolster so that it will slide up and down better it looks good.
 I followed this by cutting, drilling, and bending the parts for three more side frames.

I have yet to drill the holes to hold the journals, and the 1-1/8th in bearings holes.  Then after this set is done I will have to make another set for the trucks wheels and axles that Robb has.

I am glad for how much work I got complete today.

Monday, May 05, 2014

First Arch

Today I made the jig for bending the arches, as well as bent the first arch.

First I cut off a section of 3"x1/2" steel.  Sanding one side smooth as glass with a power sander.

 Then I scratched the horizontals and marked the hole positions with an awl.
 Then I checked them all with a calipers to see if the mirrored points were equadistant.  Only one hole in the lower right was out of position.  After checking I deepened the holes with a duller awl.  Then over to the drill press.  First i used a small center drill to mark each hole, then a larger center drill.
 Finally I used a 1/4" drill bit to drill all six holes.
 The pins are 1/4" rod.
 I then made the clamping bar.  The first arch was cut to length and drilled with the large clamping bar made yesterday.  Then I assembled it on the jig.
 I first tried to bend it with a vice grips, that did not work.  I made a bending bar like nelson locomotive works suggested.  It works best to have the bender as close as possible to the pin.  I will be making a second short clamping bar to make that easier.
Last was back to the drill press with the long bar to drill the 4 outer holes.   One arch completed.  Eight this size and 4 large ones per car means 23 more to go.

Sunday, May 04, 2014

Trucks

Today I started work on the trucks for the utility flats.

I made 4 bolsters, and the drilling jig.

I also bought oak for the journals and bolts to hold it together.   Tomorrow I will go get a 1-1/8th inch drill bit to make the holes for the bearings.

Saturday, May 03, 2014

Ready

Today I got the Storage Battery Truck running on all 4 batteries.  I installed the brake wheel.

I need to make the speed limiter pot.

I need to make mudflaps over the wheels to protect the electronics from splashups.

Next is to work on the trucks.

Sunday, April 27, 2014

Done?

No I am not done.  But the machine is assembled and will run in forward and reverse.  The downside is that the speed limiter is not working correctly.  There is a punchlist of other items also, such as hooking up the second set of batteries. Making the onboard controls work.  Figure out how to get the bow out of the top. Buy and install the large batteries.  And of course limit the top speed.  When the machine is up on blocks the speed is topping out at 11MPH.





Saturday, April 26, 2014

Control Board

Today I started to mount the control board.
I added a second board to mount the direction switch and the speed limiter onto.
There were some setbacks.  Such as not putting the direction switch in a good spot.  It was interfering with the circuit breaker and power switch.  I also had trouble crimping the small wires.  That was solved by soldering a larger wire to the lead and crimping to that.  Tomorrow I will install the direction switch.

Friday, April 25, 2014

Attach The Frames

Today at lunch I ran over to Radio Shack and Staples to get electronic parts for the Storage Battery Truck.  When I got home Nancy and I dug a trench across the grass for the new drain.  The plan is for the cement work guys to be here on monday.  Issue is on Monday I am flying to PA for the week.

After dinner I mounted the bodies of the cars to the frames and sanded Jonathan's car a little bit.  Then because a couple boards were long I used the router to shorten them.  Then I used a plane to round the edges.  Followed by some sanding.   Then Nancy took over and sanded and added some wood putty.  She also sanded and wood puttied the gondola.

Tomorrow I hope to make significant progress on the control system.

Thursday, April 24, 2014

Mount The Controller

Today I broke the controller board.   It is fixable.  I broke the thermal sensor on the aluminum plate.  I just have to dig it out, get a new one and solder it in place.  To run without it I either need to have the two wires tied together or apart.  But my board could overheat until it is replaced.

Spent over an hour on the phone with Robb planning the controls.

I also cut down the board so that it will fit vertical in the machine.

Last I found a switch for my forward reverse use while on machine based control.  Good day overall, with some setbacks.


Wednesday, April 23, 2014

Back to Work

Today I started the assembly of the storage battery truck.   If I ever make another loco I will know lots of things not to do.
First is do not make clearances so tight that paint makes things not fit.   
 The brass slides needed to be filed down inside and out before they went into place.  And again after wards.

 Don't tell Nancy but I scratched the paint in a few places.
 Once on the outside face.
 After getting the wheel assemblies in I realized that I wanted to make the 4 holes that hold the top in place larger.  I tried with a hand drill.  It just torqued out of my hand.  The good news it did not scratch the outside paint.
 I then set up a table at the drill press.
And because the drill press is not bolted to the floor I had to crank the drill press table up snug so that newtons laws would drill a hole instead of lifting the drill press.

After these photos were taken I started adding the electrical switches.  I have the On-Off and the circuit breaker in place.  The cable is run for the direction switch.  But I have to find myself a direction switch.  And mount the direction switch.