Friday, January 26, 2024

Railway Post Office In a Trolley

In Plano they have a stationary Trolley from 1911 that has three sections,  a post office, for whites and for others. 
To hold the metal to the plywood I used the Ikea bolts I had on hand.

I decided to add some strength to the center of the table front to back.  To do this I cut out most of the L flange.
I used my mill first to put holes 3" on center.  The small bed size made it not fun so I did five holes on the mill and the other 13 on the drill press.
I like this wood top on a metal hopper.
The door at the Trolley museum looked like it uses hardware for box cars.



I drilled in the holes for the nuts, used a stop block so i would not go to deep with a brad point drill bit.
My metal bandsaw blade broke. I was using it to 'chain drill' and use a cold chisel to knock all the teeth out.


To know where the holes line up I made this jig.


This is the fixture in progress.
This is the first bolt installed.
I was trying decide to use long or short bolts.  I ended up using all long bolts.  The middle one will be short because the motor is there.
 

Thursday, January 18, 2024

Desk

 

The indicator says that Anna is not in the house.
Has not had an accident in 48 hours. 
I cut the C-Channels to length.  I can not perceive a difference in length.  Then I routed both ends of the top to accept the C-Channels.

Sunday, January 14, 2024

sharpening

 

I waited to long to sharpen my planes.  Partially that helped me get the look I wanted on the desk with tearout.  Yup I wanted the tearout to make it look handmade not machine made.
After sharpening both planes per Rob Cosman's instructions I moved on to sharpen five of six chisels per his method.  I also used the diamond stones to sharpen the knife.  I asked for help making a cover so the blade does not cut something nor does the tool get dull.

This last one was so messed up on the backside that I went with the flow vs fixing it.   The back should all be flat to the left side.  It is rolled about 10 degrees to get tip and right side flat.  The front side is also angled to make a very skewed chisel.
We picked up a bunch of these little micro computers.  they have i2c, color screens, esp32 processor, wifi, bluetooth and lora.  
Zoom in on this chisel.  The bad section of the back was from thumbnail to tip,  it took 5 hours to fix it.  The right corner of the tip still needs to be done.

Wednesday, January 10, 2024

More Planeing

 I sharpened both my hand planes.  Following Rob Cosman method.  I think I liked it over what I had done before.  

Also did some research about dinkies in early iron mines.
I like the bump out under the cab windows  There are several shots around the internet of the quickly built line to the Soo from Cuyuga iron range.  And some of standard gauge trains tipped over on soft track.  Online it states that the mine used dinkey's starting with one loco then two or three to pull the 8 wood tippers out of the mine.  
I have lots of books to not read in my collection.  Maybe I should take the time to read them instead of watching videos.
I did not like the stain on my desktop.   Too blue  grey.


Below is a 1885 shot of Chandler mine in Ely MN.  I suspect the carts are hoisted up not that they go behind a rise or into a tunnel.  Oh wait, online the track in the front goes into a tunnel then up a hoist, at least that is my suspicion.   There is someone who is already an expert on this mine.  Minnesotahistorshop.com has a better version of the same picture.
So I used my freshly sharpened planes to remove 0.020" of thickness from the top. 

Saturday, January 06, 2024

Desk and Boxcar

Found an example in a Soo Line History book of what I want to do in On30.
A photo of my two larger planes.  A 9" long sweetheart #5 and a 12" #4 for roughing.
I used them to flatten the top for my desk.   This is a case where having the pictures in order will tell the story from glued to the plywood, epoxy the holes, flatten the top, sand, stain. 

Nancy, Anna and I went up to a book store in Denton.  On the way home we stopped at Kimzey Coffee.  Anna and I were enthralled with the architecture and decor.   
The stain, English chestnut, looks purple under the bright white LED, it looks warm and red under an incandescent.  
Another photo of building the Soo.
I did use the power planer as a first pass.  Even so my arms hurt.  I made sure to use my right arm as I favor my left.  My right arm hurts more than the left.


This shot of trains in black hills, three levels.  

After getting flat we flooded it with rubbing alc to see if we like the color, or wanted it darker.  This raised the grain, then Nancy went over one last time with sandpaper to 220 and the plane set to a .003" shaving.
I thought of fuming the oak, but that would have make it more grey tabaco than dark brown.

I also am adding the details to the boxcar.  
We will end with the look after doing epoxy and before flattening.  Nancy will add more epoxy and we will sand back to a flat final look.  Then I need to work on the underside to attach the legs, bracing, etc.  
 

Monday, January 01, 2024

Boxcar and Desk


 

I escaped from doing work between the holidays.  
So besides working on the vac pump, that I was going to use to put the top on my desk.  I started putting the remaining work into my boxcar.  The lumber door is a based on T&P 31919, it hinges down vs slides over.
The side door is based on St. Louis Iron Mountain & Southern.  A iron ore hauling railroad in Missouri.
I have had the grab irons and other details for months.  Just not in the mood to drill the holes and mount them.   Well really I wanted to not use typical Philips or slotted screws, but did not want to spend the money on scale hardware.  After seeing a car built with screws I said that is good enough and bought a box and went forward.  
For the desk top, I laid all my nylon and oak on top to hold the boards flats.  It would have taken too long to get the vac bag parts and starting with such a large projects was suspect to many opportunities for less than stellar results.
After putting the top on I flipped it over and added front and back edge banding to hide the plywood.  Tonight I cut the 4 edges to final dimension with a circular saw and a straight edge.
We also visited home depot to obtain round top brads to hold the hardware on.  
Most of the ladders went on fine, except the bottom rung.  For some reason nothing was cutting the angle iron.  New center drills, sharpened center drills, new drill bits for steel, old drill bits.  I had 24 holes 3/16" to drill through and it was not happening.  For the end grab irons I mounted just above the angle.  For the side and stirrups I used a burr to thin the metal and then punched out a hole with an awl.  Then used JB weld to glue the parts / screws in place.
The doors will not open on this car.  They are just for show.
I have to go research and learn how to set up the brake staff and air release valve.
I think I will add an airline to this car.  Not planning to have brakes, but having a line end to end gives options.  
An example of the holes needed for the bottom grab iron.

Looking at prototype cars for ideas.  And listening to podcasts, such as No Dumb Questions.