Sunday, June 19, 2022

5th crossbar is short

 For fathers day I was given a ratcheting crimpers.  The few times I need one a year this should help as i do not have the hand strength to use a regular crimpers.

I turned no gonk parts today.  I did a bit of reading and video watching.   Then I thought I need to do a little on my workbench.  

So I laid out the top center crossbar and cut the first half of the dove tails with the table saw.

They are too deep so the part is 1/16  shorter than intended.

My options are to ignore it and use it.  
Glue in fillers.
Make a new one.
Shorten the other four cross pieces to match this one.

The bench is 26 and 7/16 wide now.  The top is 26.5 at the center and tapers off a 1/16 at the vice end.  Narrowing the bench appears to be the best of the options as that will help me get rid of the top parallelogram. 

Saturday, June 18, 2022

More gonks

For fun and stress relief I turned more pear.  Hats, bodies, and noses.  
I also started working on the bench again.  The top has corner bracing, I stared planning the installation of those.  And cut the center cross member to length.  It is held in with blind dove tails, I think I will use a router to cut away the majority of the wood.  I don't want to do that inside and have dust everywhere.
 

Wednesday, June 15, 2022

Two more days of turning

 

Today I turned some hats.
Yesterday I turned and apple, pear, and sapote bodies.   I need to do two more hats and a few noses.  I am letting Nancy or Anna finish them and add the fur.

Monday, June 13, 2022

Turning

 As a change of pace I turned a gonk from the pear that I absconded with. 

Due to a crack his hat is backwards of what I normally do.  His nose it at the chuck, then the hat, a peg to connect his hat to his body and then his egg shaped body.   His hat is stained red mahogany, same as the top of the SBT, and covered in HUT.  His nose and body is coated in beeswax.  After he is cut apart a crease is sanded to the top of the hat.  Drill a hole for the hat and for the nose.
Add a beard and he looks quite distinguished.
I have 8 more blanks outside, more to come tomorrow.   He has already been returned to whence he came.  His caretaker squealed with glee at seeing him and said he can go inside.



Sunday, June 12, 2022

Done with Leg Mortise

Two done.
Three done.

Four done.

While working on the last joint I had a board fall into my knee.  Several hours later it still hurts and is swollen.
I helped my neighbor cut up a tree that fell in their yard.  For the selfish reason that is it.  As a bradford pear the wood is good for turning.  So I helped with the big stuff, so I could take it home.
This morning before church I let maple run at the school.  She chased a rabbit about 1/8th mile before loosing it.  Then would not stop for another 1/8th mile looking for it.  She was still panting hard when she was home for over 20 minutes. 


 

Saturday, June 11, 2022

New work shop

The high today was over 100.  The garage faces due east and gets the morning sun on the uninsulated door until about noon.
I got up and in 2.5 hours got one of the mortise in place.  At that rate, two a day on weekends and one each weeknight.  I will have them all done on Friday.
Depending how much time is spent catering to the needs of others.
So I found a new workshop.
The air conditioning increased my productivity.
The carpet was softer on the knees.

I would work on the hole a little, vacuum up the chips, and then check my work.   
I was able to complete four mortise today.  I set the far side on to check how well they aligned and they were all naturally within an 1/8th of an inch side to side where I wanted them, and up down with spot on for all of them.  

After getting Anna from work I started a fifth one,  that required marking the other leg assembly and hogging out all the holes in the garage first.  I have a little cleanup to do on the fifth joint.  It is a little too tight.  It looks like at this pace I will have a frame together by tomorrow evening.  Cutting 5 days off my morning estimation.  
 

Friday, June 10, 2022

Mortise

 Measure 8 times drill 40.  

Strawberries blond
The pipsqueek has 20 flues.  in a 5-6-5-3 arrangement.  
and I did the layout and started drilling the mortise for the cross bars.


Wednesday, June 08, 2022

Cross Bars

 

I used the bandsaw and table saw to put tenons on the cross bars.

Nancy has made a half dozen pens this week.

Tuesday, June 07, 2022

Cross Bars

The final width will be 26-3/16"  With one board in the middle.   I cut the cross bars to length to make my width.  They will have 2" tenons on the ends.  19-1/4" will be shown.
The boys took a late afternoon nap together.
 

Monday, June 06, 2022

Wider

 Today I picked up another red oak board and made the top wider.

The planer blades are dull,  I could only get a 64th off at a time and it was still complaining.  I waited five minutes between passes.

It was not enough, I still had to hand plane the last four inches of the last pass.  Because the motor temp sensor went.
These two pictures show before and after a pass.   Note the snipe at this end.

Remember the snipe... on all the boards ... that adds up to being a 1/8th inch narrower at the ends than in the rest of the glue up.   Ooops.  

Sunday, June 05, 2022

Shop Visitor

Going back to my archives.  I had a shop visitor.  He wanted a closeup.  Then I moved him out to our grass.

Jim's new roundhouse and turntable.  

I gave a rodent a triscut.
Some older pictures of the bridge in progress.
We visited an O scale layout.  





 

Top Tenons done

 

I worked on the 70 year old bridge again.   Replacing more broken Z bracing.   It was cardboard and brittle.  The new ones are stripwood and brittle.  I am almost complete on the project.   Maybe one or two more sessions and it will be ready for paint.
I also squared up the top tenons in the legs.  It was hard to keep all four sides in plane with the top cross members.  
Nancy made three good pens and a 'purse pen'  The dark redwood was not behaving so it got too thin, then when put together the CA on the outside cracked and got cloudy.  
One issue of the bridge is it had a 21 foot clearance.  Modern doublestacks need 23 feet.  We decided to remove all the wood braces from the end and reapply them at different angles to give the clearance.  It is more work but most photogenic and realistic option.  
It feels good to have another step complete on the bench.  
I plan to set the bench to level and mark the bottom of the legs and remove a 1/2" to set it to level in the given location of the garage.  It may, if I decide to move it, not be level in another spot, but that is something I will deal with then.   If the floor is more than 1/2" out of level in the six foot distance I will rethink my plan.