Friday, February 17, 2023

Spring Prep

 The time to run trains outdoors will soon be upon me.  

  • Grease and oil each bearing
    • Loco2
    • SBT
    • Rider
    • Brake
    • Flats
    • Coal car
  • Loco2
    • Add an MU power shutoff to allow to be slave
    • Increase voltage to amplifier
    • New top?
  • New boxcar
    • Add roof
    • Add roofwalk
    • Add doors
    • Add grab irons
    • Order and add door and brake hardware
    • Make trucks
    • Paint
  • Choose events to attend
    • AV&W spring meet
    • Grapevine March show
    • 2 more live steam events
  • Work on other projects
    • Lay track on On30 layout
      • Lay homosote
      • Lay track
      • Wire layout
    • Chess boards
      • Sand
      • Seal
      • Deliver
    • Useless Nook
      • Hook up RP board
      • Start 3d design and print of table
      • Start creating the structure

Monday, February 13, 2023

All chisels sharpened and another chess board

 

I wanted to make sure I hooked up the wires the same way they were before.
When I sharpened my chisels I first made a 25 degree wood block, that warped in the water.  so I made a plastic version.  That worked better.  But sure made a mess.
I took my bar clamps to the O scale club to enable glueing up the modules.  
I rerouted the incline on the home layout.  It was too tight for standard bachmann On30 cars, this longer route has a large radius and less steep grade.
I took the DWF O scale guys my unfinished boxcar.  Most of them model the same era as the car so it was good to hear their input.
cleaning up my desk area I found a couple hard drives from 2005.  This one is tempting to use in my book nook.  It just looks cool.
Another shot of the DFW layout space.   We (they) are doing a major overhaul this year.  Replacing four modules of the yard and realigning the tracks on nearby modules, this will enable the portable layout to run three loops.   Before we could only run two.  There will be a three track yard and an industrial area.  This means four trains can be kept busy.  Then there is a passing siding for the outer main.  That increases train count to five.  When the layout is at the shop we plan to have a turntable and engine facility, a passenger yard with station, and a freight storage yard that will not be portable.  I am championing the idea of having an interchange with the portable trolley layout that will add five more freight industries and the trolley passenger traffic.
I bought a Lux cutter head for the planer, tired with how short the steel carbide knives last.  I run a lot of dirty weathered wood through it.  At the same time I replaced the damaged motor drive belt, replaced a broken tensioning spring, and replaced the circuit breaker as it was tripping after 3-5 minutes of light use.  Then I replaced the power cord,  It was a 14 gauge 6 foot cord.  I always ran it plugged into a 50 foot 12 gauge cord.  I cut the cord in half and wired it in,  now I have a 25 foot 12 gauge cord.  I hope this helps.   As for the carbide head.  I ran some maple through.  It is very smooth in the grain direction, but as each cutter is at an angle I can feel waves from side to side.  I am sure someone has done a review of the machine and measured the waves,  someday if I have some wood and my indicator out I will do the same.
Sunday, I decided to procrastinate and make a second cutting board.  I mean chess board.   I learned a lot from the first one, but the gaps, sanding gouges, and misalignments made me confident I could do better.  I glued it up, and the top side looks great, some gaps on the bottom, but I can rub sawdust and glue into those.  I will add sacrificial strips to the edges before I sand so I do not add a slope to the last square.  
The inner main of the layout getting plaster leveling for a smooth ride from end to end.  
Did you know that the motor of an old hard drive can be used as an encoder?  It can also be a stepper motor.  I have arduino breakout boards for both functions.
Making a mess of my work table with the plane flattening the first checkers board.  
The first board after a coat of oil.  It has a more rustic home made feel to it.  Not bad, just not high precision.   I think I will make a set of checkers to go with this board.  

Sunday, February 05, 2023

Sharpen a chisel

It warmed up to 70 degrees today so I went on a bike ride with the kids.
I also used my boxcar as a workbench for sharpening a chisel.  The metal dust and water went all over the car, and turned it grey.  The first coat of coloring the car.  

I also cut an reglued the chess board.  The board has some gaps and mis-alignments that makes me think I will finish it as a rustic basic board vs add brass and an edge.  

The other issue is I broke my planer.  The circuit breaker tripped and once it reset I turned in on with wood in the machine.  The drive belt melted.  I used the opportunity to install my carbide spiral head.  I will also replace the circuit breaker, change the 6 foot 14 gauge cord to a 25 foot 12 gauge, and replace a broken chain tensioning spring.  I will also clean the rollers and the bed.   

Friday, February 03, 2023

Rework complete - new rework

I took the time to shave the truss so the roof sits centered.  Then I planed and sanded the top smooth.  It is ready for the finish boards.
The method of clamping raised the last band of my chessboard.  My first thought was sand it flat.  But that would leave a wide gap on one side.  I will cut it off and replace it.  The jig for cutting squares is still available.
On the way to the dentist I saw double headed track mobiles at Trinity Plant 192.
  • I need to sand the ends and far side of the boxcar.  
  • Weather the wood
  • Install the roof
  • Install the trucks
  • Install doors
  • Install the grab irons
  • Install brake rigging
  • Paint the car
  • Design the stencils
  • Stencil the car
  • install safety chains
  • Buy a new pickup so I have a way to carry the car to events.



 

Thursday, February 02, 2023

Rework will be required

I measured, test fit, then glued and nailed in the rafters on the roof sections.  Then I test fit them again.  I immediately removed the last one and replaced it.
The other three I left in place,  I will have to trim and shim them.  They looked great in the test fit.  But very poorly in the final glue up. 

 I also made a flat and square glue up fixture for the chess board.   I had moved the saw between cutting the maple and walnut squares.  Next time I will not be moving the saw once I set the square size.  I had to go back two rows twice to replace a piece that was slightly small.  

Wednesday, February 01, 2023

Not the boxcar

I started laying the rail for the On30.   The radius is too tight, the flanges are rubbing on the coupler pockets.  I could either only run 4 wheel cars, or redo this area.
I made this from a couple layers of plywood to hold a phone while charging. 
I used a circular saw to remove some subroadbed.  I will cut a new piece to go under the upper level then up along the side and back of the layout.  This will open up the radius and lower the gradient.
I have been thinking of making a chess board with walnut and maple since Christmas.  Took the time today to cut all the squares.   Because the walnut was such small blocks it did not make sense to me to glue two boards next to each other and cut.   This also allows me to randomize the maple and walnut positions so that it is much more difficult to find the sister pieces.  
It looks like the bottom walnut piece on the right is a little light.  I may have to swap that one with one of the coasters blocks.