Friday, July 31, 2020

Legs

So I went from a mounted foot to carved legs.

I decided it would be easier to mount if I carved a body than if I tried to glue up the figure.  By using wood I can get a realistic structure under the clothing.   No I am not reaching into the uncanny valley, just good enough.  Kinda like a SBT that uses round rivets instead of square bolt heads.
I carved a route for the antenna wire to run inside the right leg.  The signal wires will all do the same.
For a test the legs are taped together.  Final assembly needs to be robust enough for life on the road.   I could glue it up as I go, with a hope I never want to take it apart.  Or I could glue and screw... can I make is strong enough?

Tuesday, July 28, 2020

Right Foot

Do a little every day.   Yesterday I chose to make the battery charger more robust I added a plate to hold onto the wire.  I can if I want add a knob to use to pull on to disconnect.
 Today I carved away at my wonderfully carved shoe to make room for the antenna and signal wires. 
 I also added a hole to screw the shoe to the foot board.
Checking the fit, I need to shorten his legs just a little as his pants are down in the back.  Do I modify the legs to the figure or make a new legs.  I already cut the figure at the joints, and I don't plan to get another set of clothing. 
 I am still working from home.   The morning routine involves being outdoors.  Maple joined me for a bit.
She could not get comfortable so she left within five minutes.   I had to go inside shortly after as rain was due.  Nancy was driving and got stuck in a red area of the weather map for an hour.  We only saw green at the house, ten miles apart. 

Sunday, July 26, 2020

The SBT Sound System

I annoying the rest of the house by playing lots of loud sounds on the SBT.  My wife asked me what the smell was.  It was the RRE sound box getting too hot.


So after conversation with the engineer at RRE we thought that I was supplying too much voltage.  I found an IR thermometer and did a test.   With the supply voltage at 12 or 24 volts I sat idle or played lots of noise.   24V was fine enough with no sound but it heated up and stayed hot with noise.  The 12 volt was fine in all conditions.  It was less loud, but no garbled sounds either.  

The end result was the decision to supply the RRE with 12v from an external buck converter.  It needed 2amp at max use so I found a 5amp unit.  
 So for one last time for hopefully a long time I stuffed the electronics bay of the SBT. 
 Such a jumbled mess of wires.  When I began I was hoping to have a nice clean looking setup.  I can put a cover over it all if I really cared.  There is a USB to the sabertooth and a micro SD extension cord for the wav trigger.  The only reason to dig to the bottom is now to update wav trigger firmware.
 I also added a new battery to the Odometer.  It does speed too, but unlike before it is not in an external box. 
 I have room for the log book in the loco.  Now that I am turning pens I can make my own custom one to ride along with each one. 
At one point I had the recharging transformer in the SBT but I think it got too hot and blew.  Now it is external.  My goal is to have a second battery set on charge while running.  

So what is next?

September is a meet at White Creek, I plan to bring this and Loco 2 there to run.  
  1. The end of the charger needs stress relief to the keep the wires from breaking.
  2. I only have one transmitter for both locos so I can only run one at a time or MU, I need to bet Robb for the radio.
  3. I need to make the person.  Lets break that into parts... 
    • Feet
    • Legs,
    • Waste,
    • Arms,
    • Head.
  • He will be a lot of work as there are 25 signal wires for the sound system plus the radio antenna running from the right foot up the leg.  Only 13 wires are in use at this time, pondering moving the spedometer output to his backside.
  1. The MU is a loose wire inside.  To use it the cover needs to be held up or I need to notch the cover or drill mounting holes.  I am worried if in use someone sits on the cover pinching the wire.
  2. I need to customize the program
    1.  I can have a few more sound triggers.
    2. The volt and amp meters.
    3.  The onboard speed and direction control.
  3. I also will need custom programming on the handheld.  Horn and bell work, but I can take away the rear headlight and brake trigger and add two sounds.  
  4. I need to make my data logger.  It will be an external box that connects to terminals inside.  Then I can transfer it to another unit.
  5. I need a toolbox to hold the radio and charger, maybe a second set of batteries.

More turning

Today the remaining items needed for the well of the SBT arrived.  I started the install this evening.  First is the buck converter to drop from 24 to 12 volts for the sound amp.  More on that in the next post.

The last pen made was a bullet click pen.  This one is special as Lilli did most of the work to make the blank.   I did the final sanding and sadly, I realized that wet sanding with micromesh is pushing grey into the pores of the wood.   Not being a part of a group or having a teacher is resulting in learning lessons the expensive way. 
I have been drinking lots of sweet tea.  I dilute is with lots of ice.
Nancy made a bolt action pen.  She rather enjoyed.
A couple pictures of turnings I started while my parents were here.  On the left is mango, the right is a maple with bark inclusion.
The mango set includes a bookmark.
The bark inclusion maple on the photo rock.
And on the lathe.   I do think that if we keep this up I want to get a wood lathe as I do not want to swap back and forth.  Getting all that sawdust on the lead screw is really going to mess with the drive.  
I am really finding this pen quite nice.
Jeff and Robb did a switching event in Michigan without me.
Looking at a modified USRA 0-6-0 vs the 2-6-0 prototype  I like the looks of.  I do not feel drawn to the point that I want to empty my bank account.
Nancy and I spent a lot of time Saturday out by the lathe.   Maple needed to be out there too.  She took some time out from watching for people using her sidewalk to rest in the shade.  Not often we see her sleep outside.
Nancy turned her seam ripper.  She turned 4 things today.  One an acrylic on a mogul kit from turningz was a failure.  That is two failures in that set of kits, one of mine had a loose top.  The one she had the mechanism was not working.  Then not knowing how to disassemble she used a pliers to pinch the mechanism.   I need a proper pen vice for assembly and disassembly if we are going to continue to do this.
Jeff gave me the start of a tank.   He is working on making a 2-6-0 steam powered.  I wanting an electric joked he needs to make double so I can have the pretty looking failures on my loco.  I guess that starts with a tank body.
Back to tools of turning.  I stuck a bar in a holder of the quick change to allow me to have a toolrest.  The quick change is in the way of the right hand.  It will work for turning a few things a year.  Doing one a week... I think we should start looking for a proper wood lathe.
Our initial turning set.  These small tools are really meant for fine turning.  We should bite the bullet and get a proper large gouge.  But I really want to stop the wood turning bleeding.  We have too much initial investment, I suggested we only reinvest based on what we have.  We have a number of fair pens we can sell to start the process.
A reminder of how the mango started out.  I like the idea of the bookmark, but it is a lot of hand sanding to make look nice.  Not bad if watching TV.  I did most of my work while Nancy was at the lathe.  

Thursday, July 16, 2020

Pen Turning Pause

 I forced myself to stop turning pens for a bit.  Lilli got a fish tank, and my little coffee table was the perfect size to hold it.  Wanting to make a second table anyway I chose to make a half scale farm table.  Starting with stair balusters  I cut them to length, then put them in the lathe.  Using all the knowledge gained from watching you tube videos I went to town.   To make a straight cut I used the cranking cut of the carbide tools.   Then I cut down to a smaller diameter, checking with an open end wrench.  Cleared most of the waste away by cranking, then a little hand work to clean up and 80, 120, 220, and 400 grit sand paper.  The result is four nicely tapered legs with a round area at the top, a bead detail separating.

I remembered to get a picture of the before.  This came with the taper going the wrong direction.  Also to get a long enough leg, some of the square section needed to also be turned. 

I am working on an oak table top to go with this set of legs.  The top will get a natural finish and the rest painted.  I also will go back and make a second table.  Slightly smaller than the one I am doing now.  This one at 14" wide is too wide to be planed by machine.  I am learning a lot about hand planing, and because I did not pay attention while gluing up I have opposing grains in my boards, resulting in tearout issues.  Went old school and mixed sawdust into polyurethane to fill in the voids. 

Not sure if I will use a wide plank teak for the second table, or oak again.  Maybe keep it narrow enough for the planer. 
I broke the june budget and got a computer.  I enjoy small ones like my Acer 1410 or my asus T100.  Sadly neither one is good enough to run Cad systems of any quality.  This Asus is twice the size, a 15.6" touch screen, a gen 8 I7 processor, 1tb solid state HD.  I wonder how much more power this machine has than my college pentium 90.  I chose to download fusion 360 for personal use.   I think I will see how one of these 3d prints, as well as try out the CNC etcher to make a wood version.  The plan is to draw up all of pipsqueek so I can plan then build it over the coming years. 

Soon I will be getting back to the SBT.  The root cause is that the amp did not like being fed 24 volts.  The box got too hot.  So I have a 24 to 12 buck coming, then it will be assembled, hopefully for a long time.   Then I can work on the guy. 

Mid July in Texas, soon it will be too hot in the evenings to work in the garage. 

Pen Turning

I finally paused long enough to work on the lathe.  I found an issue with the quick change for the drive screw.   One of the gears was messed up.   After a conversation with the seller of the lathe he reminded me that while he was moving the lathe on dollies it fell over onto its face.  The selector lever seen in the bottom of the picture above broke and he replaced it.  As the gear system worked before that point he did not put it through it's paces.   He was able to use it on a reasonable threading rate like 16 per inch.   I on the other hand was at the other extreme of slow feed rates for getting good finishes, then the drive screw would lock up once per revolution.   The honest guy that he is he found a new old stock part and we will replace the damaged gear.   Sadly that gear is the smallest one in the drive chain, as well as the one used most often. 

So without the drive system and wanting to use the lathe I decided to turn some pens.   I was given 12 kits for fathers day. 

 This is my third pen, the first one from my own wood.  In this case a maple stick from the firewood pile from the old house.  I had used the rest of the wood for shop projects.  While this pen looks nice, when I wet sanded the wood got too wet, swelled, and the area at the tip is warped and broken apart.
 This is my first turning.  HDPE with a waxed finish.  Quite a nice pen, the plastic is black with flecks of blue that add a galaxy look.
 Experimenting I made this pen and pencil set.  They are from oak with a shou shugi ban finish.  The caramelized wood smells wonderful and since I brushed off all the soot it is not transferring to my hands with use.   I expect these to wear with use, turning a wonderful golden oak color where gripped. 
 This is my mango pile.  The finished pen is cross grain, the bookmark is long grain, and the two blanks sets are the same long grain.  The cross grain was weak, and with a dull tool I had a catch that shattered the pen.  I was able to super glue it together all three times that happened.  I also glued some teak dust into the holes.  In the end I have a wonderful pen which for some reason has one half greyish and the other a nice golden tone.   I may have used dirty sand paper, or because I turned each half a few days apart.  No bother, it looks great and feel great.
  Here is the first 8 pens.  My first turning is at the top, the future ones at the bottom.  1) HDPE, 2) Rosewood, 3) maple, 4) Maple, burnt and brushed, my favorite. 5-7) Oak burnt and brushed. 8) mango cross grain.
 Here is another picture of the maple shou sugi ban pen.  This one has a lot less depth variation than the oaks, but should with use wear into a nice warm finish.
 Under different lighting.
Along the way I took another blank of the HDPE and made a case, this stuff being plastic was quite a pain to work with.  I would be happy turning the rest of my pile into ties.  I think I will set a piece outdoors and see how it handles the weather.