Friday, January 03, 2020

SBT Internal Wiring Almost Done

Today after going around with Nancy to gather carpet quotes I installed 47 micro farad capacitors on the motor lead and replaced the damaged capacitor on the LED driver.  I chose not to risk having sparks fly out from the capacitor and onto the wav trigger and sabertooth. 

Next on the list below is to order the charger.  I have four 12100 AGM batteries set up in a series parallel configuration.  In theory I think I can discharge and charge at a rate up to 24V 6A as it is a cyclic load.  If I do that I want to set a higher empty condition so I do not damage the batteries.  Battery University recommends charging at 0.3C with a 3 stage Constant Current - Constant Voltage Float Smart Charger.  If I have a 20AH battery pack and I should charge them fully over the course of 12 to 16 hours that means I am looking for a 1.5A charger.  I found 1.5A and 2A chargers on ebay.  I also need to buy the Anderson Power Products battery connectors.  I think I will get a few as I used all my spares. 

Now as I am waiting for Robb to come home from work so I can modify my program I think


A few items still remain. 

  • Buy a battery charger.
  • Get raw arduino program from Robb
  • Reprogram rear headlight to be a sound trigger 5 volts
  • Reprogram analog 2 to be voltage of batteries for 9DoF data collection
  • Fix tether direction 5v as signal may be backwards. via program or resolder switch
  • Sort all the trigger leads
  • Put 12 trigger switches in the person
  • Mount the person
  • Make a toolbox for tools, spare parts & charger
  • Make actual sound files
  • Mount MU terminals
  • Hook up MU wires
  • Test all functions
  • Hook up 9DoF
  • Program 9DoF
  • Test 9DoF

Thursday, January 02, 2020

SBT Rewiring

This is the new wiring diagram for the SBT.   I see that the image above is lacking the DPDT at the MU master slave.  The punchlist for the machine is getting shorter. 


  • Install capacitors on the motors  10 to 100 micro farad 
  • Buy a battery charger Single 24V with appropriate amp rate.
  • Reprogram rear headlight to be a sound trigger 5 volts
  • Reprogram analog 2 to be voltage of batteries for 9DoF data collection
  • Fix tether direction 5v as signal may be backwards Either in program or resolder switch
  • Put 12 trigger switches in the person
  • Mount the person
  • Make a toolbox for tools, spare parts & charger
  • Make actual sound files
  • Mount MU terminals
  • Hook up MU wires
  • Test all functions
  • Hook up 9DoF
  • Program 9DoF
  • Test 9DoF

Wednesday, January 01, 2020

Repowering the SBT

 A before picture of the SBT's onboard controls.  I shortened the wires on the direction switch so they would not be caught by the batteries.
 A few shots of the electronics bay at the start of today's work.  I have been taking some pictures but have posted on 7-8th.info instead of in blog posts.  Today is a jumble of past work uploaded to keep things all here for reference.
 The power connector is mounted to the side wall, next is a terminal strip for the speaker / amplifier.  The last thing on the side wall is the LED driver.  It is powered at 5v, Robb says this is OK but it states 9v-30v input.
The white box holds the switches, inside is for MU and 9DoF (the terminal strip is for that purpose also.  On the outside is the 24V circuit breaker I think the same 30A one, or one from a razor scooter.  Then the power switch, from a razor scooter.  The three switches are the radio / onboard choice switch, then the grandpa switch, then head end direction choice.  Last is a volume pot. 

 This is after today's work.  I ran an antenna wire and a 25 conductor cable from the electronics well to where the right shoe of the driver will be, this will run up the pants leg and end in the torso.  The antenna will be in the head.  The other wires are for sound triggering.
 Through the battery tray, a tight fit to with the onboard controls.
 When I made the hole into the electronics bay I used sheets of paper and tape, lots of tape, to protect the electronics from the metal dust.  I used a die grinding bit in the dremel to do the work and vacuumed often.  I plan to use some putty to seal the openings as there is a small chance of water intrusion. 
This is the tray to hold the RX box, it goes above the sabertooth, it has magnets in the feet to hold it in place.  Other than the antenna wire all the other wires will be long enough to allow moving enough to access the sabertooth and sound card for reprogramming.
 A  couple pictures of my 7/8ths info group swap.  From Bill Martensen I received a series of crates. 


 The new lever for the SBT.  This one has a magnetic catch at the pivot but is held to the cable with a pinned lock block.  This was made before I decided to permanently apply the person. 

 Forward and reverse with the lever.
 My practice carving shoes, I don't think any of them are right... so I made one more that was for the right foot.
 Soon I will be gouging out the top of this shoe for the wires.

 I took a break from the SBT to make button coasters.







The sander kept throwing the drive belt, Lilli and I tried wondered if we could fix it. 
 The final 47 before finish application. 3 Pine, 8 Plywood, 8 Oak, 13 Mango, 11 Walnut if I remember correctly.
 Back in time to before the switch cover was applied.

This shows where I plan to keep the log, I will need to have a support toolbox as there is no battery charger onboard.  I do not own a charger yet that will work.  At this point the 9DoF will also be a separate box that plugs into the SBT.  I think it may be a tool I will want to use on other locomotives. 

Remaining items to do:
Double check all wiring installed, confirm no shorts or breaks.
Hook up signal wires to the wav trigger.
Install the RX and hook up the wires.
Program the wav trigger.
Program the sabertooth.
Test the basic setup.
Make the 9DoF box.
Program the 9DoF.
Make correct sounds.
Apply driver to seat.
Make triggers in the driver. 
Show off.

Thursday, October 31, 2019

Kiosk in 7/8th scale

 For the 7-8th.info 2019 swap I started with the top of a lamp, and worked down.  The idea was to use craft sticks and make a simple project such as crates or a small building.
 Rather than use sticks from the store I had Nancy's help making my own from some of the oak I had on hand. 




 I tested out the different options of staining it.
 In the end it was an undercoating of black ink with a covering of red stain on the outside and teak oil on the inside. 


 The jars were filled with some of this stuff. 




 To close the door I added a magnet and a little chunk of steel as a latch. 
As usual my phone and windows and blogger do not do photo rotation well.