Sunday, January 29, 2023

more roof progress.

 

I weighed the roof down to keep the angle the same as the top of the body while the glue dries.
One of the CNW yards had a tramway in 1943.  Not sure which CNW yard it is, I took the photo from the internet and saved it as 1943 CNW yard.
Friday night I glued the side banding in place.
Saturday I visited the O scale group and we did some work and a lot of planning.
Here are the roof section on Friday. 
I am reading a book about narrow trains in england.  The max speed of operation is the same as the gauge in inches.  With freights at half that speed.   7.5" trains should then go about 7 to 8 mph, that I agree feels comfortable max.  Though I would inverse that, slowing down with passenger loads, faster with less dynamic loading.
This trolley layout was started in the 80's.
Saturday night I sat in front of the TV and put the end edge pieces on.  
Another photo of the car as of Sunday night.   Next is to install the trusses to the underside of the roof.  Only the center rib is glued and nailed currently.   To keep the roof where i wanted it I pinned one side to the body, glued the center rib to the side, glued the second side, then pried up the roof removed the pins and squeeze out, then put it back into place.

Tuesday, January 24, 2023

Edge banding

 

Today I cut down the plywood roof sections to size and made the banding to go around the edges.   
Not shown is the brace I cut to strengthen the roof peaks, they are in the car.  

Monday, January 23, 2023

Sub Roof

 

I think this might be the first time I have used the kreg jig properly.  I have owned it for at least 5 years.
This is the N scale I own
I glued on the side and end pieces.  I am quite happy with the look, a bit of a gap in the corners, some sawdust and wood glue will make those dissapear.
This is the N scale Nancy owns.  
We bought this picture for a couple bucks at the train show this weekend.  I cant make out what railroad.  The brakemen on top are a nice touch.
The top side of the center brace.  This needed to be glued and screwed because the sides were bowing out.  If I had made the top "latch over" the sides  I could have gotten by without the brace.  
I also cut the plywood for the roof.  Half of it was in the attic as a floor for storage of stuff.  I will have to replace that with another chunk of wood at some point.  
A close up of the front of the locomotive.
I bought the boxcar, Nancy the loco.   I also bought an On30 porter and 9 tippers.  That brings my total to 48 of those.

Wednesday, January 18, 2023

Roof truss

 

I made the roof truss and ends.  I plan on two sections to the roof that hinge open.  Along with these 8 pieces I cut two long skinny side pieces.  
We paid a plumber to dig down and find a root in our drain.  It was in the cleanout not the main drain as expected.  
I cut the end triangles off.  The one goal was to not cut too far down... 3 of the 4 corners I did good.  One of them, not so much.  I will clean it up with the hand plane and sander.
As a reminder, this is what the siding started out as.  

Tuesday, January 17, 2023

Siding Installed

 

We saw this on our morning walk.  I am glad I got a picture.
Tonight I glued the center section of the first side,  and all of the second side on.  20.5 on the end, 88 on top.  The doors will be glued over the top of the siding.  I did this so the area that hangs down over the frame has plenty of support.   I may come back and add filler between the wood and frame vs letting it hang down an inch like it does currently.   

Monday, January 16, 2023

Installing Siding

 

I cut the siding for the sides today.  All to 14-1/4 inches.  The ends are 13-1/2 inch, the metal end sill is the remainder.
First I glued both ends in place.  One board is narrower as seen on a prototype.
My drink... mt dew with a scoop of ice cream, which caused all the bubbles to release.
I have both ends and a start of each end of one side.  I have to measure for the door then fill in over to it.  

Sunday, January 15, 2023

Chamfering the siding

The setup to chamfer the siding went through a couple iterations.  
I needed the board to be held down and held over to the fence.  Some of them warped and needed more pressure than others.  For the last pass I added some weight to a sprung hold down shoe.
There is 220 pieces to make. 
The first two samples I made I pained white and red with spray paint to confirm they looked good.
The neigbor is getting rid of a home made boat, I snagged it to use the foam for sceanery.

This is the first iteration of the fixture.  Most of the wood that went through this one was rerun on the last run to get a more consistent chamfer.
I cut the end boards to length.  Quite happy to have cut them.   Only 21 boards per end.


This is all the siding on the car side, some of the pieces are tall enough to be two boards.  


For the chamfering I had a blower sending the dust away, better to keep the table clear of problems.

I am quite happy to be doing this.  Even if the car will be painted.  I can tell the car is individual boards, not painted plywood.  I do not have a plan yet for the roof.  I am thinking of 2 or 3 sections.  I could use hidden cupboard hinges vs having loose sections that will have to be set somewhere.  

What is left to do?  

  • Grind down the machine screws to flush
  • Fix the area damaged by the sander
  • Glue the end boards on
  • Cut the side boards
  • Glue the side boards
  • Cut the top angle pieces
  • Buy door and safety hardware
  • Install the doors
  • Paint
  • Stencil
  • Make the roof

Sunday, January 08, 2023

More Siding / sheathing for the boxcar


 I now have 180 of the needed 220 pieces.   I think I will run a few extra in case I mess up adding the chamfer.  I can use the extra to make boxes for the SBT.

Saturday, January 07, 2023

Working On the Box Car

 I spent a couple hours looking for prototype cars photos on the Pre-depression Era Railroad Modelers group on facebook.  IE the one group that is the reason I still have a facebook account.  I only looked at photos uploaded in 2022, and found the ones here interesting.   

My car will be 1.6" scale, with the arch bar trucks I made, It will be a furniture car.  It will have the single board siding dimensions or 5/8" wide and 1/8" thick.  It will have 1/16" chamfer, I think they have to be accentuated a bit.
 I also will need the top to be a narrow board above the siding, then a wide board for the roof.   The narrow board will protect the glued on siding.  The ends will have the triangle of wood the same as the narrow board.  
My car is 61 inches long, that is a 38 foot car.  There was a Michigan Central series of Furniture cars of the 11105 number series of those dimensions.  I copied the height of that series, but am not planning to match the door or other details.  







At first I was thinking of having a more unusual end, either some form of steel, or wood.  I am now shying away from that option.
I was impressed with this series of cars for Piano movement.  They had 12 cars.  I have not decided if I will have my car be a private car like this, or a railroad owned car.  

If I had not built the body I think I would have made a covered gondola like this photo shows.


The challenge with having an end like this is the lack of end sill sticking out.  I would loose room to the next car.  


This end is neat, but do I have the skills to model it?
The box car body was held to the frame with 30 12-28 flat head bolts with slot drive.  After they were installed they were ground flush.  I got 12 of them in again, the rest refused to be installed.   That size screw is rare, replaced with 1/4-28.  I ordered a pack of 50 hex drive replacements from bolt depot.
I turned my sander into a thickness sander.  It has enough power to send a board the whole length of the driveway, into the road.  I only did that once.  I also had one stave kickback off the table saw.  Glad I was standing to the side as it was impressive in how quick it disappeared with a bang.

To get them to work I had to drill out the hole, use a 1/2" drill in reverse to enlarge where the slope of the head goes, then tap the metal 1/4-28, starting with a drill, then switching over to hand power.  Then I could use my impact with a 90 degree attachment to install the bolt, sometimes starting or finishing with and allen wrench.   One of them took me a 1/2 hour to install, because i did the 1/2" drill after tapping, and the bolt just would not start into the metal.
I will have to grind the bolts flush at some point before installing the siding.
My first attempt to cut siding I used a ripping blade, the one that was in the saw for a long time, it burned a lot.  I did what many you tubers recommend, to have the keep piece to the left of the blade and keep adjusting the fence.  I got a .67 millimeter of variation.  

My next attempt I used the fine finish blade I had in stock, scrubbing it with a brass brush first, it still had some burning, and the consistency was the same as before.  
This evening I purchased a new fine finish blade, and switched to having the fence fixed and keeping the piece that came off the right side of the blade, between the blade and the fence.  I did end up with a few boards that were not against the fence on the tail in and had to be rejected.
I get 5-7 boards per starting board.  I need 220 total for the body of the car, a few more for the doors.




In total I set aside 38 of my boards to get the wood from.  About a 1/4 of my remaining stock.  About 1/2 my stock has defects like knots, figure, or weathering that it can not be used for scale siding, I will make a few more end tables and such with them.  
We tested the fire place.  The wood we bought feels wet, good news is I have enough scraps to dry it out while burning the kindling.  
I set up a quality check on the side of the railcar.  Five of my first run of boards stay up and I place other ones around them and check the feel.  I suspect I will do a light sanding after I have all boards in place.