Sunday, June 19, 2016

Tugger Lights

Today was a continuation of wiring the tugger.  I traced out the issue I was having to wiring up the master power switch wrong.  It is a lighted switch an rather than use + and - to power the light I was using the + and + this put the light in series with the LEDs, the LEDs did not get enough voltage, and displayed red or yellow to tell me so.  I fixed that by running a - to ground on the battery.

I also ran wires for the two LEDs on the board.  One is for AC power, the other for battery power.  To charge the batteries all three must be on.  (The master power switch is really a battery cutout switch.)

Now I have another issue.  I have a short between the housing of one of the lights and one of the light leads.  This is causing a green or white light in the LED.  Once again an error telltale.  I tried quick to isolate the LED board from it's own housing but that did not work.  I could try isolating it even more, but the proper thing to do is to pull out the wires for the lamp and replace them with ones that have full insulation and not shorting out on the housing or copper conduit.   The wires are held in with some expanding foam at the underside to keep water out.  I found the cut insulation, right at the end of the copper conduit.  When I cut the conduit I left a burr on the inside, and the wires chaffed against it.
The three lights conditions:

On AC power, the batteries are charging when all three lights are on.
 On battery power when both red lights are on.
 System turned off, no drain on batteries when all lights out.
Lights are powered by AC, batteries are cut out, not charging when switch is dark.  
 My other project today was to finish the bench for Nancy.  I made a fixture as I had 6 holes to drill and counter bore.

Saturday, June 18, 2016

Tugger lights

 Today's project is to change out the charger for the tugger.  I was using a car battery recharger plugged in underneath.  It was big, bulky and disorganized.   I purchased a charger for a security system as an alternative.  A 16volt transformer and circuit board.
 We decided that we wanted to have the charge port and on-off switch on top, at a fender, so we had to drill some holes.  To reach the hole I used an old half inch drill and a brace.
 This is a replacement back side to the battery compartment.  The old one had a on off switch and charging port.
 Here is a picture of the new charging plug and power switch.  It will be disguised as a toolbox.  I needed Anna's small hands to help me pull the wires down and through.
Finally a test.  The charger works.  But I am having a problem with the lights.  When both were hooked up, they stay red.  When the top one is hooked up it is yellow and flashes red once a minute.  It does not seem to be the charger as the same happens when going straight to the battery.  Polarity does not change the issue.

Friday, June 17, 2016

Planer

Today to check out the new planer I picked up I started on a project for Nancy.  New wood for a child sized cast iron and wood bench.   I am about 80% complete on the project.

Monday, June 13, 2016

Horse

David Newell of Pike River Northern posted a photo of a car stand he made from 2x3 angle on facebook.  I have been thinking about how I need one for a while, to reach the underside of loco 2.   His design was quite simple, using the same metal throughout.  Starting with a 20 foot stick of metal, about 10 foot of each becomes the legs, and the other ten feet is the bridge.  The top bridge bolts to the two uprights, allowing for disassembly.  Large castors on the bottom allow for rolling about uneven floors.  He then powder coated his and indirectly offered them for sale.

Mine is made from 2x2 angle, is just over ten feet long, and will bolt in three sections.  There will be four 5" diameter locking castors, currently on backorder from Menards.  I will not powdercoat but I may see if it can be blasted and primed, or at least sand and paint it.  The height is such that it will just fit under the train storage shelf when it is not needed.

The added benefit is it is space where I can park railcars if I need to shunt things around.   It is hard to believe but the storage shelf is almost full.  There is only 3 feet of empty space before I need to develop a method to get to the upper deck, make a lower deck, or stack rolling stock.  The temporary storage this and the van and truck shipping tracks provide might be enough for a while.

I guess there are other options, store somewhere else, sell or decommission, stop getting more... change back to O scale.  I have been thinking about long term planning of the traincars I want, there is an end in sight,,, just not very close.  One constraints Nancy gave me is I need to be able to move the whole family, that is 5 cars... nominally 5 foot each, a locomotive and a caboose, granted this is when the kids are teens, not tomorrow.  Then there are a few decorative cars I would like, such as a tank car.  Then there is the SBT, and trucks to go with it.  Currently that is the two troublesome tanks, but I think a string of 10 trucks bobbing behind would look wonderful.  Lots of planning, dreaming, engineering, building, and showing.  But this is a long term hobby.  I am trying to limit my self to one car a year.  This year it was the brake car, or was that the coal car, or Loco #2?  Next year, a box car, or a gon, or a flat, or a caboose, or some trucks for the SBT, or all of the above.

scrap bin

Did not work on the stand Sunday.  I did take a look at the coupler mount.  It was a failure.  gently shaking the coupler and it would walk right on out and fall off.

Saturday, June 11, 2016

Stand

I am making a sawhorse stand to work on locomotives and other railbound equipment.  This will allow easier access to the underside than the table top methods I have available currently.   Yesterday I picked up two sticks of 2x2x1/4 angle and today I cut all the parts for the legs.  I made one mistake in the angle of cutting a one of the legs... it became a bottom brace and I took a chunk of steel I had on hand to make the leg.  It is a little thinner but it will work.  

Tomorrow I will drill holes and bolt it all together.  Then later I will get it welded together.

I also made a stick to put in the coupler to hold either the camera or an end of train device from a scrap of oak and six button batteries epoxied on to hold it in place.

Saturday, June 04, 2016

truck loading

We took some train cars and loco 2 to Iowa Model Live Steamers.

Here was our setup this time.

 A tarp held down with straps, and bungees in the corner.
 Under that a moving blanket to protect the tarp from sharp edges.
Each car is held with two straps.  One around each coupler and held from rolling back and fourth.  The wheels ride outside the 1x2 guides for left and right.  The center coal car has a moving blanket to protect if the cars sway side to side.
Below the deck two flatcars are parked.  The camp chairs were also placed under the deck to keep the cars from rolling.

This setup worked fairly well, it did not take too long to load, tie down or untie and unload.  While driving we did hit some rain, and having the tarp inside the bed resulted in rain at the edges before and behind the wheel well.

Tuesday, May 31, 2016

Doors

This afternoon I cut the channel for the doors of the boxcar.  Drilled holes and installed them on the car.  


Nancy and I also tied down the rolling stock and took a ride through the neighborhood alleyways.  It worked well.  

Nancy and I also removed the plastic from the decals.  It worked much better waiting a day.  There are a few pulled / distorted serifs but nothing that can be noticed at 5 feet away.

Then it started raining.  We got a out a tarp... eventually it filled with water and started filling the bed of the truck.  When the rain slowed we emptied the water and parked the truck in the garage.

Monday, May 30, 2016

Truck

Thank you Nancy for going to the hardware store three, or was it four times today.

A sheet of 3/4", some 2x4s some 1x2 & screws.  All so I could empty my shelves.




No not like this the cars are too close together.

Better.

By raising the cars above the wheel wells they can be separated.  And the flat cars fit underneath.

Next is to tie the cars down.

Saturday, May 28, 2016

box

This morning after breakfast I wanted to take a nap.  I stayed up too late last night.  Remembering something from a Scott Adams book I choose to get dressed and go outside and organize the garage and get ready for making a box around loco 2.

I used the skill saw to cut off the sides and end boards from a sheet of 1/2 inch plywood.

I cut them oversized and trimmed to size on the table saw.  I found by cutting on the left, then rotating 180 and moving the fence slightly I was able to have two parallel cuts in three passes.

The same was done for the two roof sections, with a 7 degree angles cut on a 1x6 to stiffen the ridge.  It is strong enough for Lilli to sit on.  All was assembled with gorilla glue and 1 inch brads.

The doors were cut with a jig saw.  Two side doors and one end lumber door.

There is lots of work left to complete:
Reset the journal positions to tighten the chains.
Pin the journals so they do not move again.
Make doors from 1/8th ply.
Put blocks in the corner to mount the box to the frame.
Rewire the charge system.
Rewire the drive system.
Make and install brakes.
Make real body.
Add details such as ladders and brake rigging.
Add a volt and amp meter.
Add an spedometer and odometer.