Saturday, January 07, 2023

Working On the Box Car

 I spent a couple hours looking for prototype cars photos on the Pre-depression Era Railroad Modelers group on facebook.  IE the one group that is the reason I still have a facebook account.  I only looked at photos uploaded in 2022, and found the ones here interesting.   

My car will be 1.6" scale, with the arch bar trucks I made, It will be a furniture car.  It will have the single board siding dimensions or 5/8" wide and 1/8" thick.  It will have 1/16" chamfer, I think they have to be accentuated a bit.
 I also will need the top to be a narrow board above the siding, then a wide board for the roof.   The narrow board will protect the glued on siding.  The ends will have the triangle of wood the same as the narrow board.  
My car is 61 inches long, that is a 38 foot car.  There was a Michigan Central series of Furniture cars of the 11105 number series of those dimensions.  I copied the height of that series, but am not planning to match the door or other details.  







At first I was thinking of having a more unusual end, either some form of steel, or wood.  I am now shying away from that option.
I was impressed with this series of cars for Piano movement.  They had 12 cars.  I have not decided if I will have my car be a private car like this, or a railroad owned car.  

If I had not built the body I think I would have made a covered gondola like this photo shows.


The challenge with having an end like this is the lack of end sill sticking out.  I would loose room to the next car.  


This end is neat, but do I have the skills to model it?
The box car body was held to the frame with 30 12-28 flat head bolts with slot drive.  After they were installed they were ground flush.  I got 12 of them in again, the rest refused to be installed.   That size screw is rare, replaced with 1/4-28.  I ordered a pack of 50 hex drive replacements from bolt depot.
I turned my sander into a thickness sander.  It has enough power to send a board the whole length of the driveway, into the road.  I only did that once.  I also had one stave kickback off the table saw.  Glad I was standing to the side as it was impressive in how quick it disappeared with a bang.

To get them to work I had to drill out the hole, use a 1/2" drill in reverse to enlarge where the slope of the head goes, then tap the metal 1/4-28, starting with a drill, then switching over to hand power.  Then I could use my impact with a 90 degree attachment to install the bolt, sometimes starting or finishing with and allen wrench.   One of them took me a 1/2 hour to install, because i did the 1/2" drill after tapping, and the bolt just would not start into the metal.
I will have to grind the bolts flush at some point before installing the siding.
My first attempt to cut siding I used a ripping blade, the one that was in the saw for a long time, it burned a lot.  I did what many you tubers recommend, to have the keep piece to the left of the blade and keep adjusting the fence.  I got a .67 millimeter of variation.  

My next attempt I used the fine finish blade I had in stock, scrubbing it with a brass brush first, it still had some burning, and the consistency was the same as before.  
This evening I purchased a new fine finish blade, and switched to having the fence fixed and keeping the piece that came off the right side of the blade, between the blade and the fence.  I did end up with a few boards that were not against the fence on the tail in and had to be rejected.
I get 5-7 boards per starting board.  I need 220 total for the body of the car, a few more for the doors.




In total I set aside 38 of my boards to get the wood from.  About a 1/4 of my remaining stock.  About 1/2 my stock has defects like knots, figure, or weathering that it can not be used for scale siding, I will make a few more end tables and such with them.  
We tested the fire place.  The wood we bought feels wet, good news is I have enough scraps to dry it out while burning the kindling.  
I set up a quality check on the side of the railcar.  Five of my first run of boards stay up and I place other ones around them and check the feel.  I suspect I will do a light sanding after I have all boards in place.

Thursday, December 22, 2022

Box Car Siding Standard Dimensions

 

In the process of making a limo
The bench got a coat of oil.
I also rearranged the shop to get these two train cars ready to bring out to the track for storage.  That would free up eight square feet in my shop.
With the help of the extension I could drill clearance holes for the vise screws.   If I had planned ahead the bench would be two inches wider it would be much easier to install the vise.
A while back in a state of productive procrastination I cleaned up this corner of the shop.  Moved all the stuff out, vacuumed and put the stuff back.
The vise is made of oak, same as the rest of the bench.
I found some very pretty wood at the side of the road.  I have a plan for this wood.
To drill the vise screw clearance hole in the leg I had to add in some temporary wood,  I tried pine first but the drill bit drifted into the soft wood so I had to redo with oak scraps.  
The vise clearance hole is 3/4" in the leg, the rest is in the air.
The tops are bolted to the legs.
Some of the o scale club
I used a diablo 1-3/8 bit to drill the hole.  the screw at the front makes it VERY aggressive.  
The vise in place, it is glued in place... the top is bolted on...   well at least the vise is not glued to both the top and legs.  I never plan to take the top off the legs.
I made a quick frame for under the gondola.  This is so it can be parked on storage rails.
The bench with one and no layer of oil.
Adding corner braces being installed.
There are two standard sized of box car siding.  
Looking at the bench back upright.
Finished diagonal brace.  There are one in each corner.  They were not fun to install, I did not do great at tight joints.
This boxcar is a future project.
This is an underside view of the top holding bolts.
I want to have the vise gears blued over silver.  I will use the heat an linseed oil method.
This is how far in the vise screws go in in the closed position  I could have had more overhang.
To sand all the surfaces, and to install some braces on the bottom to allow it to be lifted with the lift the table went upside down.
Then onto sides for epoxy to fill the cracks and holes.

Puff Puff Puff Puff Puff
The underside of the O scale modules.

Wednesday, November 23, 2022

Catching Up

Some more out of order pictures because I was not taking the time to upload.

Cletus is inspecting my start at learning IIC with arduino

The coal load in the tipper came out.  I decided to make it a flat rather than a tipper.  
The paint came off with the glue.
Maple and Cletus tolerating eachother.
I cut some live oak into boards for a friend.

I made a lot of table top trees, Jon made one.
Here is my setup to cut the lumber.  a sled on former treadmill board.


The 21st was take your child to work day, I took Anna, she liked the coloring, the scavenger hunt, and calling all of us nerds.
Earlier this fall I went to TN to play trains.  I took some pictures on a rock face that is open to climbing.  Amazing to see people taking the short way up.
Anna adopted a companion.   This 11 week old puppy will grow into a fine protector and motivator for her.
The top is from bachmann the trucks from a brass import,  I have to attach them together.
One guess when I took the photo of this antique.
The annual funky finds fall show.  We made a profit, and bought a dog.
I want to make a book nook.  I may not share as much as I want to.  Unfair to give hints to solving the puzzle hidden within.  It involves Arduino with IIC breadout boards.

One last picture from TN.  I have more saved on my phone, when I find a cord I can upload more.