Nancy finished finishing the base of the lamp.
I screwed the horn onto the base.
Attached the cord to the base.
Installed the touch sensor.
Attached the wires.
Attached the cover.
And then fixed another lamp.
Take it apart.
And put it together.
And the lamps work.
Wednesday, January 09, 2019
Sunday, January 06, 2019
Fixing Hollow Core Bi-fold Door Handle Blowout
More productive procrastination, this time I got tired of how our closet door handles are always loose because the doors have no filler in the middle.
In the case of our pantry door they had drilled two holes for the handle about a half inch apart. Opening and closing the door had worn the holes so much that they were one and the knob flopped all over.
The door because of the soft material it is made from, the pull is attached to the back side, it acts like a spring. The all thread screw then acts like a file, slowly removing material making the handle looser.
The first step is to remove the door handle and go to the back (inside the closet) side of the door.Using the hole that is present drill out a larger hole, I used 2-1/8th hole saw. The MDF is quite soft so go easy drilling. *see note below.
With this larger hole we can now see inside the door. Measure from the back (inside) face of the front panel to the back (outside) face of the back panel. (Measure the thickness of the door so you know how thick the plug needs to be.
The next step is to make a plug to fill the hole.
First drill a template with the same holesaw.Draw a circle on a scrap of wood the thickness of the door. This wood is from a pallet, cleaned up on a table saw. First roughly cut a circle on the band saw.
Then sand to fit snug in the test hole.
Back at the door, apply glue to the two flat surfaces. This will attach the plug to the front panel.
Push the plug in slightly, spread glue around the edge of the plug to attach it to the back panel.
Tap the plug home.
Clean up all the glue squeeze out.
From the front side drill a hole 1/64th larger than the pull knob screw through the plug.
Install the knob, this is the clamp to keep everything tight until the glue dries. Clean up the sawdust and tools, close the door and admire your handywork. The door handle will feel oddly solid but you will get used to it in a few days. Speaking of, 24 hours later come back and remove the knob to touchup the paint.
*This MDF is soft enough to use a utility knife and files to make a square hole and use a square block. Alternatively purchase closet rod and a hole saw of the same diameter to save the bother of making plugs.
Saturday, December 29, 2018
Electronics Inventory & Plans
Beyond all the basic resistors, capacitors, switches I have collected I have a few other items that I plan to use.
- Sabertooth 2x32 (2, one in Loco 2 one for SBT)
- Radio control system in Loco 2
- 6-12-24 volt backup charger meant for emergency lights in tugger to charge lighting system.
- 2-12 volt marine charger onboard loco 2 to charge those batteries.
- Arduino Nano (6 of them unused)
- Nano 3 expansion board so I can use screw terminals
- 9DOF Razor IMU
- WAV trigger robertsonics (polyphonic sound playback board)
- TRRP connectors for MU 6 unused
- Ion Air Pro lite Wifi HD sports video camera
- TRRP female female cables for MU (should be at least 2 maybe 4)
- Four function radio switch, used in brake car
- The control guts from several scooters and power wheel toys
- Digitrax zepher and supporting system (have offered for sale several times)
- MP3 player YS-M3 SD MP3 playback module
- Keyed switch
- A couple of 16x4 breakout boards
- Nokia 5110 LCD
Projects
- Data logging of grade, curve, amp, volt and speed step for any my locomotives
- Have: 9DOF and a Nano
- Need: volt / amp meter modules if not already on loco.
- Loco for use on home railroad / kids loco able to pull two loaded flats
- Have:
- Need:
- SBT radio control
- Have: Sabertooth, nano
- Need: Radio system, amp meters, light control, batteries, 3d printed person for radio antenna, Onboard control integration
- SBT sound
- Have: Polyphonic sound
- Need: Speaker, amp,
- Brake Car controlled by loco radio control
- Have: Working brake car
- Need: RX module
- Force sensor MU for Pipsqeek
- Have: Arduino Nano
- Need: Gauge, battery
- Dead rail On30 for Shay, 2 porters, 1 davenport, 2 trolleys
- Light for little library
- Camera system with 1 second time-lapse
- Wireless MU (radio connection)
- Electric steam engine 4-6-0
- Caboose
- Tool car
- New tenders for Pipsqueek
- 10-12 trucks to go with SBT, one with power assist
- Ballast tamper
- Gondola
- Box car (Sprayberry is working to offer a 1923 ARA steel car)
- Build Sprayberry coal car (waiting for trucks to come in the mail
My planned 3 trains:
- 1.5" Pipsqeek, baggage car (water tender), passenger car (fuel tender) with force gauge to MU loco and additional cars if desired.
- 1/4 scale SBT, 10-12 trucks as flats, tanks, and gondolas, 1 power assist (probably loco 2 with new cover)
- 1.6" 4-6-0 DSSA or M&NE steam outline electric, M&St.L 4570 boxcar (tool car), wood reefer of a Michigan theme, working hopper car, NYC 418137 hopper car with On30 layout load, 6' composite gondola (Pere Marquette), 36' flat, 36' flat, DSS&A caboose.
- Tugger, Loco, pink utility flat, blue utility flat, wagon car
Monday, December 24, 2018
Finishing Projects
The coasters are getting closer to being done. We sanded with 3000 grit paper and now that the shop has been dust free for a few days applied one last coat.
Nancy got a french bulldog and was going to give it to a friend with a bulldog mix, I suggested painting it to match, it dropped and the legs broke off. After an unsuccessful glue up I drilled a 1/16" drill to pin the offending leg, broke the bit off inside with glue surrounding to make a stronger joint. Then I added a tail with a piece of copper wire and green putty.
Then onto the painting, I showed Nancy how to do washes and dry brushing (dry brushing on wet paint melds in overnight... learn something new all the time.) So we could get the markings correct we "borrowed" the dog for a few hours.
The last task of yesterday was changing all my acrylics, they were upright in two boxes, making it hard to choose. I made six trays to lay them in. Then Nancy helped me bring down all the other boxes and I cut down and or divided them as needed. Then I wrote the basic contents on the end. The only thing left as multiple layers that probably should not be is the electronics boxes. It was one box, now it is two layers of two, I should go back and make it four single layer boxes.
Sunday, December 09, 2018
Coasters
With the trains at work or stored in closets, sheds, boxes and garages it was time to work on another project.
This week I took one of the pieces of wood from india that had promising grain (x) and cut it to size for coasters. First was cutting to width, then in half for the thickness by ripping on the bandsaw. Then sanding, lots of sanding. Wore out the paper on my 36 inch belt sander. I installed a new blade on the table saw and cut to width, more sanding. Then some test finishes, beeswax, Howard feed-N-Wax, three different stains, and polyurethane. We are not going to stain the wood as it hides the grain.
We are also working on the base for the trumpet lamp. We plan polish up the base and the coasters with a really high grit. The coasters will also get a backing, I think flannel.
This week I took one of the pieces of wood from india that had promising grain (x) and cut it to size for coasters. First was cutting to width, then in half for the thickness by ripping on the bandsaw. Then sanding, lots of sanding. Wore out the paper on my 36 inch belt sander. I installed a new blade on the table saw and cut to width, more sanding. Then some test finishes, beeswax, Howard feed-N-Wax, three different stains, and polyurethane. We are not going to stain the wood as it hides the grain.
We are also working on the base for the trumpet lamp. We plan polish up the base and the coasters with a really high grit. The coasters will also get a backing, I think flannel.
Saturday, December 08, 2018
Trains at work
A coworker brought in some garland to work and considered it decorating their cube.
Nancy and I brought in two mountains, trains in On30, N, and 7.5" eleven rolls of wrapping paper.
Four little trees, and some other stuff. To one up them. It started a full on war, there are now lights hanging all the way around the ceiling, almost every desk is decorated, and there is a festivus pole.
With pipsqeek at work I started other projects, including wireing up a trumpet as a lamp.
Making a winter scene in O scale for work.
And searching out articles of 4 wheel tenders for plans.
Nancy also helped me unpack the Sprayberry hopper car.
For a $675 car it is amazing how much this car is going to cost me. There is shipping of the car, the trucks, and the detail parts putting the total near $1400. I have not yet added rivets, riveting tools, paint, decals etc onto the list. There is a reason finished cars sell for $2600.
Nancy and I brought in two mountains, trains in On30, N, and 7.5" eleven rolls of wrapping paper.
Four little trees, and some other stuff. To one up them. It started a full on war, there are now lights hanging all the way around the ceiling, almost every desk is decorated, and there is a festivus pole.
With pipsqeek at work I started other projects, including wireing up a trumpet as a lamp.
Making a winter scene in O scale for work.
And searching out articles of 4 wheel tenders for plans.
Nancy also helped me unpack the Sprayberry hopper car.
For a $675 car it is amazing how much this car is going to cost me. There is shipping of the car, the trucks, and the detail parts putting the total near $1400. I have not yet added rivets, riveting tools, paint, decals etc onto the list. There is a reason finished cars sell for $2600.
Subscribe to:
Posts (Atom)












