Sunday, February 07, 2016

brake car pt 3

 Nancy took some pictures of me yesterday.





 Today I attached L brackets to hold the battery from sliding around.  I used long screws then cut them off with the dremel on the backside.  Note, dremel sell these quick change disks, I don't recommend them, they don't stay perpendicular to the shaft.
Then to keep the battery up off the screw heads I gorilla glued a masonite panel under the battery.  Wax paper to keep from gluing the battery down.
 I also drilled the mounting holes for the power switch, circuit breaker, and the relay.  Also the air compressor mounting and steel mounting panel to base mounting holes.
I had read once that a little bit every day on these projects keeps them moving forward.  As I spent most of the day resting from a sinus headache it was nice to get some work complete.

Saturday, February 06, 2016

Brake car pt 2

Today's project is to make a mounting platform for all the small parts of the brake system.  On top is a place for the gauges, around the side of the battery is a place for the relay and on off switch.
 First is making a template from cardboard then transferring it to a sheet of steel I had laying around.
Then because I do not have a brake to bend the metal I used my arbor press and heat from a propane torch, and a hammer and an adjustable wrench to bend the part into shape, after cutting it with a hacksaw.
 I also put in slots for holding the tank and the battery in place.  I will have to add L brackets around the battery so it does not shift.
 A poor photo of the backside, or maybe the other side of the shop...

Thursday, February 04, 2016

Brake Car

 Tonight, I wanted to ruminate over loco two, so I started assembly of the brake car.
 First was seeing if it would all fit.  I cut the reservoir to length.  Then I also drilled a three inch diameter hole in the base plate under the reservoir, this gives a better mounting point than the dome of the PVC pipe.  
 I decided to place the electronics on the far side of the battery from the compressor, this will keep them slightly cooler, and by mounting the power and reset switch low I do not have to remove the cover completely to turn them off.
 I will be keeping the gauges, needle valve, and volt meter up high for easier reading during setup.  Well maybe not the volt meter.  I suppose I could have had a flip open door for the reading of the gauges and the switches on top, I can make a new box or a caboose later if I really want that.
This weekend I will continue the install of the brake system.  The challenging part will be hold downs for the battery and tank, and a panels for the electrical and air components.

Wednesday, February 03, 2016

Upright

Tonight I drilled the base plate for the four L braces holding the pedestals.  A slow steady process to get the holes in the correct location.  Measure, measure again, mark, mark again.  Measure, drill a small hole, measure, offset the hole if wrong, drill more, measure again.  It has gone well, 7 of the 8 holes were well placed and the last only needed very gentle persuasion for the bolt to threaded in.  
 Flipping the chassis over I was able to add the motor tower, the big batteries, and the charger.   On the top is a 2x2 representing the roof eve height.   Honestly I think for the height (9') the length looks a little short (19 feet) but that matches the prototype as near as i can tell.

This information is from the ORER vol 6 page 32.  The prototype photo from http://www.amesvilleshops.com/AS_Images/NYC&HR_4673.jpg .  without the knuckle i think this car is on a RIP track or storage waiting scrapping.  most likely at towards the end of life used as a MOW or other such service.  Reading the ORER these cars disappeared by the turn of the century.  
I also notice that the springs are bottomed out.  The range of motion is only 1/4", which is actually per design, but it is a lot less than the SBT.  The journals and other parts have enough flexibility for more movement, with the exception of the pedestals.

I am glad that I picked up both types of chain connections, in this case a small to big will work best for the 25# chain.  The large to large may work if I elongate the motor mounting slots.  As for the #35 chain.  That will be a large to large  or a small to large depending where I place the axles.  There is enough movement there.

Sunday, January 31, 2016

Pedestals

Friday I got the loco frame, pedestals and the coal car back from Samson's.  They welded the coal car and loco for me and laser cut the pedestals.  

Saturday I did not feel good so I stayed upstairs.  I did spend some time sorting my machine screw collection by diameter and pitch while watching season 6 of Dr Who.  What was three boxes on my shelves is now thirteen but it will take me less time to find screws when I need them.

Today I moved the guts of the pedestals from the Eaton Engineering aluminum to the Samson cut steel ones.  The advantage is the wider top with slots so I can tighten the chains.  


I also trimmed the end of the axles, and cut and drilled 1x1 angles for holding the pedestals.  Jon watched me deburr everything.  I also drilled the coupler pin holes in the engine and the brake flat, filed the loco frame that overhung the edge, and cleaned up the shop a little.  






The flat has groves for flanges on top.  I plan to park the loco on top of the flat during travel and the groves will help center the loco.  I expect the top of the flat to get torn up pretty quick.  

Thursday, January 21, 2016

Almost the last of the deliveries

Received two more deliveries today.  First was all the Clippard parts for the air brake system.  Anna and I set it all out and I have what I need complete.

Second the charger came in for No2.  This thing is heavy.  It will be mounted above the motors so it will only take an extension cord to charge the train anywhere.   After two years of running these trains I am confident that the less loose parts the better.  The SBT has the two tops, the separate speed and amp box, the controller pendant can be unplugged, we disconnected the batteries, the large battery cover, frequently took off the couplers for travel, Tad & Mike, the charger, and soon the radio control with it's batteries and charger.  The less spread out this stuff can become the better.   Soon I will make a tool tender to run with the SBT to hold it all.  Also I have stopped running the SBT with the big batteries.  This makes the extra top, and large battery cover unnecessary.  A high quality radio control will make the pendant redundant, it will be either onboard or radio control.  Last time I ran I forgot I had onboard control.  I hand pushed the loco back to the loading bay.  I could have switched control source and played some more.  I guess the fear of watching your 2 year old being taken away by a 12 MPH train stops logic.


Tonight I took the time to drill the holes for coupler pins.  I drilled them at 1/4" dia, through the 1x2 tube as well as the base plate.  My reasoning is that after the two parts are welded I will enlarge to the proper size, and they will be perfectly aligned.  I also deburred the ends of all the  C Channel that makes the side and end sills.


Wednesday, January 20, 2016

Bottom Side Of Frame

Tonight I cut and placed the four end sections of the end sills.  I have yet to deburr the parts.  I also need to drill the holes to mount the pedestals and the coupler pockets.  
In other news I cut two groves in the top of the flat car for the flanges of #2, just deep enough to guide but not that deep.  We also started putting wood putty in the holes of the flat in preparation for black paint.

Monday, January 18, 2016

Frame Parts

 I received the frame parts from the laser cutter.  It was definately worth having them bend the motor mounts.  But I did find an error, they bent them with left back and my drawing has them with right back.   I fixed it, turning over the base plate lined up the holes.

 Next time when I assemble the parts I will turn both motor mounts 180 degrees.  This will move the motors outboard more, giving slightly more room by the other door.
The bottom C Channel is nicely lined up.  Held in place with a couple of magnets.  Same with a coupler pocket.  Next step is to cut the four endsill parts, drill holes for the couplers.

The charger, motor controller, and some other parts are on order.  I need to pick up some 1/2 bolts for holding the jackshaft.  I may use carriage to provide a smooth underside.

Tuesday, January 05, 2016

Ride On Train Remote Brake System

Searches of the internet has proven it is difficult to find a well specified remote brake system for a ride on train.  There are a few pictures, and advice the Tom Bee or West Bend will sell a system, but no clear directions.  No list of parts.  No drawings like this: 
First the green, yellow and red dots indicate to myself whether I have the part, it is ordered, or I need to order.  Yes the implication is I have not yet made the unit to this design, read later blog posts to see how I fair.

The pump is a Viair 92C.  I choose this over a cheap harbor freight model for hopefully longer lasting more quiet ride.  Advice is 50/50 on cheap vs expensive model.

The pressure gauge is a non adjustable 65PSI Clippard unit.  Note that most people use Clippard parts, which helps with the hose fittings.  My needle and solenoid and gauges are also Clippard parts.
The solenoid valve I am using here is a EVO-3-12, it is two position, 3 port valve.  In one position (0V) it blocks pressurized air and the output vents to atmosphere.  In the other position (12V) pressurized air is sent to the output and the vent is blocked.  This would be used for a spring return cylinder.

The trucks are Tom Bee, with Tom Bee brakes and his cylinders, which have springs to return them to the off position.  Some people say these are cheap and do not last, others say they are cheap and work well.  A system with a Clippard cylinder could be developed.

The remote control unit is a 4 channel unit, I got one with two key fobs so an engineer and brakeman can have control of the brakes.  Look for one that will send out a constant signal until the next press of the button.  0 volt signal, valve closed.  12V signal valve open.  The one I am getting is programmable; send a signal only when button pressed, on-off, or one button for on, another for off.

While waiting for parts painting of the box continues.

Monday, January 04, 2016

painting

Yesterday I tried a few of the paints present in the house to see if any were a good railroad brown.  Decided none were.  Took the kids to Menards for way to long for a gallon of cheap paint in a railcar red brown color.  


I am applying washes each side a different method.  All are of the variation of red at the top, diluted black at the bottom and a wash over with a stiff wet brush to blend top to bottom or bottom to top.  Red on first, black on first, equal amounts, more red, mostly red.  I was told that it will go on bright and darken as it dries... that is true, it went on way too red but after an hour of searching the net about air brakes it is starting to look much better.