It did take chasing the threads a few (about an hour) dozen times to get the diameter down to the size needed for the threaded wheel to fit. It is hand tight until the last three threads, then it has to be worked with a tool. Tomorrow I will cut off the extra pot length and start wiring the machine.
Sunday, March 29, 2015
Threaded Pot
It did take chasing the threads a few (about an hour) dozen times to get the diameter down to the size needed for the threaded wheel to fit. It is hand tight until the last three threads, then it has to be worked with a tool. Tomorrow I will cut off the extra pot length and start wiring the machine.
Saturday, March 21, 2015
Electrical Planning
I set up the controller on the work bench today.
I am trying to set up a good range on the onboard control. The 5k pot the machine had would go from 0 to 12 MPH in in a 1/3rd of a turn. Much too fast for that form of control.
Here is some data I gathered from trials...
Start angle, Max speed, Resistor, Pot, Thought
120, 11.8, 0, 5k, way too fast & narrow range
0, 9.8, 0, 0, what happens with nothing is connected
90, 2, 3.3K, 1K, max speed is too slow, good range
0, 6.2, 2.2K, 1K, good max speed but slow speed is 2.4 mph if start angle was 10 degrees this would be perfect
90, 6, 2.2K 2.5K, this is good, slow end starts late, not sure how to manage.
10, 3, 3K, 1K, good but slow
110, 4, 2.68, 2.5K spot on with huge low end deadband
OK I am doing this the silly way. I have a meter... I should measure across PH and PW and get a table of speeds for each resistance. With the 5k pot. My electrical minded brother said I did it wrong. I kept the pot hooked up to the source when I measured, which skewed my readings. I threw out the suspect data, and after talking with him and realizing that I had similar results as him we did have similar results: 1k deadband at bottom 3k of range and 1k of deadband at top. Look at the poly lines not the linear ones. The chart is messy because the experiment was poor.
Note that the controller works backwards, more resistance is full go, no resistances is stop. Not safe in our mind since we have a tether that can separate (infinite resistance = fasted speed and no way to stop.)
So for on-board control I want a max speed of 4mph, that is 2K Then I need to make up the rest with 3K of fixed resistors. At least that is the theory. I am going to try 3k fixed with 1k pot & 2.5k pot to see which I like better. I will also try 2.5k fixed with both. But first dinner....
OK I am back... Added some new values to the table above in Blue
2.68k fixed with a 2.5k pot has a max speed of 4 and 110 degrees of dead band at the zero end.
3k fixed with a 1k pot has a max speed of 3 and about 10 degrees of dead band at zero.
I need to order a pot that will fit in the machine online anyway, I am thinking of getting one each of 1K, 1.5K, 2K, and 2.5K Then I can play around a bit more to dial in what I want. I am leaning towards the 3K 1K setup with 3mph max as a good option. Note that 2.68K & 1K did not stop at the low end, a 2.68 and 1.5 might.
Note: the pacesetter is really supposed to be center off. I found out after wiring up the whole machines that I should have worked with both directions when setting the resistor and pot. I was able to get it to work with what I got but top speed in forward is 4mph and 2 in reverse. Forward has no deadband, reverse has about 30 degrees.
Saturday, March 07, 2015
Rub the belly
I am waiting to work on the tankers until my axles come.
I am waiting on the SBT until the nibbler comes.
Next job is to make a stand for the table saw and jointer.
Sunday, March 01, 2015
nozzle and bands
This weekend I spent the time to install the top nozzle and the bands on the tanks.
To start I wandered around the big box construction store picking up items that would make a good cap. After reviewing options such as sofa glider pucks, electrical covers, and PVC plumbing parts I settled on a 3" PVC cap and a short section of nozzle. To get this was a 10 foot section of pipe, and two caps. Then it was back to the store for a 3.25 inch hole saw. The saw cost more than the pipe.
I started by removing three staves and putting a two by four curved to fit inside as a backer, glued in with gorilla glue and held with nails.
I cut off a six inch section of pipe, and used that to hold the cap and cut it down to a half inch. Then a whole lot of hand sanding to remove the lettering on top. I then cut off sections of pipe to use as a nozzle.
This afternoon was setting up and cutting the bands and drilling for studs with two nuts. The studs started off as one inch long 10-32 bolts cut with the dremel.
Thursday, February 19, 2015
Planning
The last wheel is my seven inch diameter curly spoke wheel. While neat I think this will be for an outside frame gravel car.
Ryan
Wednesday, February 18, 2015
Wheels
http://www.bravethinkers.com/Pages_ModelEngineering.asp I am drooling at his finely detailed spiral spoke wheels. I sent an email via the web page feb 9th. -have not heard anything on the 19th
over the pond is the Ffestinion railway. They use the spiral spoke wheels I emailed http://www.blackgates.co.uk/ they sent me a picture. It is 74.60 pounds for 4 blanks that is $113 in USD today.
http://www.chaski.org/homemachinist/viewtopic.php?f=30&t=99074&view=previous is a link to a straight spoke wheel. I emailed the guy Feb 9th heard back, about $35 to $45 per casting for six inch diameter
http://www.chaski.org/homemachinist/viewtopic.php?f=30&t=98482&view=previous Nor have I contacted these people.
http://www.chaski.org/homemachinist/viewtopic.php?f=30&t=93957&view=previous Nor have I asked about these wheels.
http://www.chaski.org/homemachinist/viewtopic.php?f=30&t=95709&view=next i could ask for some laser cut wheels or something.
https://www.facebook.com/1516604385249445/photos/a.1516623151914235.1073741828.1516604385249445/1535904066652810/?type=1&theater nice spokes for 18 dollars each. I keep coming back to these, 5 inch diameter, straight spoke.
Add this to the wheels I have started that are 7.5 inch diameter and I have the potential to have a wide variety of wheels for carts that go with the SBT. I would love to have a string of ten carts to go with the SBT, at $200 each they would cost about $2000 total. Quite a bit of cash for something I can not ride on, well maybe with proper design I could ride on them.
Fred w Hanks company sells CNC Steel wheels $18 Cleveland, Ohio. CNC machined steel wheels. 4.375 tread diameter, .500 reamed axle hole. For more information PM Kevin Harris on facebook. "We do not stock axles because of the differences in bearing sizes everyone wants to use for bearings. I usually use a 3/8 ID bearing, but others use other ones. It is relatively easy to change the hole size on the wheel, or adjust the un made axle to fit a wheel. It is a bit harder I keep the axle perfectly true when adjusting a bearing surface."
Saturday, February 14, 2015
Center Sills
First I cut two eighteen inch sections of 1x2 tube. Then I used the same template as the SBT to mark the curve. Then I marked each side one inch in for the flat on the sides. I then used the band saw to cut 45 degree off each corner. Then I used the saw to make the flat on the edge, last was cutting the edge out with the bandsaw. Then on to the hand action cleaning up the cuts with a hacksaw. Then on to using a file and the bench grinder. Last was sand paper to clean up everything nicely.
Then I ruined all my hard work by drilling two 5/16th holes on each end, one at the standard place for Tom Bee couplers, the other is for links. This is the same way as the SBT. It took some time to clean the holes up, and remove the burrs without damaging the ends.
Wednesday, February 11, 2015
Tank Flat
Saturday, February 07, 2015
Modifications, New Tools
In other news I showed the girls at Anna's birthday party my crayon art. One of them begged for this drawing, I figured it would be better to have it seen than to put it back into storage. I gave one of the other girls a drawing on canvas. I hope both of them take care of them.
Thursday, January 01, 2015
O scale Building Kits
The crispness of the castings are incredible. I would love to take the time to build this kit, to make it my own.
But I have no place for it after it is built. It would sit in a box, or on a shelf. I have done that once with a downtown deco stone station kit. Having a plaster station sit on a shelf worrying about it, it was a relief to see it placed where it belongs, on a layout, the L&MB. It does look slightly out of place but I am sure Larry will get it to blend in. The safest place for a plaster model is on a layout or diorama in a living room.
Another interesting kit.
This one with the mansard roof is not that common, it would take a lot of work to back date it from the 60's to the 1900's for my layout.
I could imagine spending hours detailing this kit.
The same with these two DPM kits.
Now that I am in 7.5" I have to choose my projects. I have a choice, I could keep these building kits in a box for years to come, in hopes that I circle back to the desire to building an O scale layout that needs these buildings. Or I can sell them and use the money on trains I use now and enjoy now. As long as they sell for at least what I bought them for I will be happy. I may be sad to never have built the Yorke kit, but other than high quality plaster castings it is just like any other kit.




