Thursday, February 19, 2015

Planning

Here is a picture of my in progress tank car.  The center sill is held at coupler height, with the boards of the flat sitting on top and the tank sitting on those.  Under it is a pair of 4.125 diameter wheels.  Next to the flat, behind Tad is a 5 inch diameter paper towel roll.  This is the same diameter as the goodman cast straight spoke wheels I like.  They do not fit under the flat.  I could have an inside frame and not have the flat stick out.  But then the people have the problem reaching the top of the tank to load it.  They need to stand somewhere.  Raising the flat and tank up will make the car more top heavy and unstable.

The last wheel is my seven inch diameter curly spoke wheel.  While neat I think this will be for an outside frame gravel car.

Ryan

Wednesday, February 18, 2015

Wheels

http://www.bravethinkers.com/Pages_ModelEngineering.asp  I am drooling at his finely detailed spiral spoke wheels.  I sent an email via the web page feb 9th.  -have not heard anything on the 19th

over the pond is the Ffestinion railway.  They use the spiral spoke wheels  I emailed http://www.blackgates.co.uk/  they sent me a picture.  It is 74.60 pounds for 4 blanks  that is $113 in USD today.


http://www.chaski.org/homemachinist/viewtopic.php?f=30&t=99074&view=previous  is a link to a straight spoke wheel.  I emailed the guy Feb 9th  heard back, about $35 to $45 per casting for six inch diameter

http://www.chaski.org/homemachinist/viewtopic.php?f=30&t=98482&view=previous  Nor have I contacted these people.

http://www.chaski.org/homemachinist/viewtopic.php?f=30&t=93957&view=previous  Nor have I asked about these wheels.

http://www.chaski.org/homemachinist/viewtopic.php?f=30&t=95709&view=next  i could ask for some laser cut wheels or something.

https://www.facebook.com/1516604385249445/photos/a.1516623151914235.1073741828.1516604385249445/1535904066652810/?type=1&theater   nice spokes for 18 dollars each.  I keep coming back to these, 5 inch diameter, straight spoke.

Add this to the wheels I have started that are 7.5 inch diameter and I have the potential to have a wide variety of wheels for carts that go with the SBT.  I would love to have a string of ten carts to go with the SBT, at $200 each they would cost about $2000 total.  Quite a bit of cash for something I can not ride on, well maybe with proper design I could ride on them.

Fred w Hanks company sells CNC Steel wheels $18  Cleveland, Ohio.  CNC machined steel wheels. 4.375 tread diameter, .500 reamed axle hole. For more information PM Kevin Harris on facebook.  "We do not stock axles because of the differences in bearing sizes everyone wants to use for bearings. I usually use a 3/8 ID bearing, but others use other ones. It is relatively easy to change the hole size on the wheel, or adjust the un made axle to fit a wheel. It is a bit harder I keep the axle perfectly true when adjusting a bearing surface."

mr-motion.net sells steel wheels machined on a CNC lathe to IBLS wheel standards. ½” center hole. The tread is 4.375” dia. Pricing : for black oxide finish is $20.00 each; for a “raw steel” finish is $18.50 each, plus shipping. Flat back profiled front.

https://sites.google.com/site/eatoncustomengineering/  is $23 per wheel or $69.95 for an axle steel wheel.  I purchased blanks, Robb made axles, and there is a noticeable out of roundness between the bearings and the wheel face.  Flat back profiled front.

plumcovestudios.com is $80 for an axle, cast iron cnc machined.

http://www.realtrains.com/files/83950612.pdf $27 for steel wheel profiled both sides.

http://btilden.com/Products.html  $340 for a set of 8 5" wheels with keyway, good for locomotives. that is $42.50 each

http://railridersupply.com/ has holed wheels for $90 each.  $300 for an axle.  

Saturday, February 14, 2015

Center Sills

Today's task was making two centersills for the small tank cars.  If I had made square ends it would have taken about 5 minutes.  But I decided to match the coupler pockets of the SBT.  I think I did a better job on these than I did on the first set on the SBT.


First I cut two eighteen inch sections of 1x2 tube.  Then I used the same template as the SBT to mark the curve.  Then I marked each side one inch in for the flat on the sides.  I then used the band saw to cut 45 degree off each corner.  Then I used the saw to make the flat on the edge, last was cutting the edge out with the bandsaw.  Then on to the hand action cleaning up the cuts with a hacksaw.  Then on to using a file and the bench grinder.  Last was sand paper to clean up everything nicely.
Then I ruined all my hard work by drilling two 5/16th holes on each end, one at the standard place for Tom Bee couplers, the other is for links.  This is the same way as the SBT.  It took some time to clean the holes up, and remove the burrs without damaging the ends.

Wednesday, February 11, 2015

Tank Flat


Today I used my new table saw and my shop vacuum to collect the dust.  I took some pallet wood and ripped all 4 sides on the saw.  I tried out the jointer, but the blades need to be replaced, too many uneven gouges.  Nancy ordered the new blades from Amazon.  

I also had trouble keeping the board flat on the jointer, it seams to rise up / rock at the middle so I end up with a thick middle and thin ends.  I will try some things later, shallower cuts, etc to get better results.  

The end result is a platform / flat car for the tank cars.  They are about 15 inch long, and will be about 11 inches wide.  Trying to decide how far I should go without having wheels... 


Saturday, February 07, 2015

Modifications, New Tools

This past spring I had purchased a pair of 30 inch long tanks 10 inch diameter.  I started dis-assembly  on one of them, to make them more scale in appearance.  removing the top platform, and PVC nozzle.  The three nylon tank bands had to go.  I also removed the oversized mounting blocks.  The last task was to split the tank in half.  Because there was an internal disk at the centerline I used my new table saw and cut just to the right and left.  I was left with two 14.5" tanks, I reused the disk for the end of one of them and got a disk for the other on the bandsaw.  My blade bends outboard as it cuts so it took three tries.  The first two I used a jig to make, the third freehand, it is not a perfect circle, but it is close enough.  Afterword I cut a 3x3 inche piece of pallet wood to fit inside from head to head, this I glued in with gorrila glue and nailed all the staves to the head with the airgun and one inch nails.  

These two tanks will go onto frames to look like industrial tanks on 4 wheel flats similar in size to what the Jeffrey company had.
I am trying to decide if I should use the wheel sets I currently have on hand, on the archbar trucks under the utility flat or get some more.


In other news I showed the girls at Anna's birthday party my crayon art.  One of them begged for this drawing,  I figured it would be better to have it seen than to put it back into storage.  I gave one of the other girls a drawing on canvas.  I hope both of them take care of them.

Thursday, January 01, 2015

O scale Building Kits

This is a Thomas Yorke Rocopila Short Line Stone Depot from 1976, when I was two years old.  One of only 200 made, though I do not know which number because the glue on the label is so old it fell off before I bought the kit.

 The crispness of the castings are incredible.  I would love to take the time to build this kit, to make it my own.



 But I have no place for it after it is built.  It would sit in a box, or on a shelf.  I have done that once with a downtown deco stone station kit.  Having a plaster station sit on a shelf worrying about it, it was a relief to see it placed where it belongs, on a layout, the L&MB.  It does look slightly out of place but I am sure Larry will get it to blend in.  The safest place for a plaster model is on a layout or diorama in a living room. 



 Another interesting kit.




 This one with the mansard roof is not that common, it would take a lot of work to back date it from the 60's to the 1900's for my layout.



 I could imagine spending hours detailing this kit.

 The same with these two DPM kits.








Now that I am in 7.5" I have to choose my projects.  I have a choice, I could keep these building kits in a box for years to come, in hopes that I circle back to the desire to building an O scale layout that needs these buildings.  Or I can sell them and use the money on trains I use now and enjoy now.  As long as they sell for at least what I bought them for I will be happy.  I may be sad to never have built the Yorke kit, but other than high quality plaster castings it is just like any other kit.

Tuesday, December 23, 2014

right angle tool

So today Nancy and I went around to Sears and Lowes and some other stores buying stuff.  Got a large vice grips, and a dremel right angle tool.  That tool was well worth it.  I was able to drill holes in seconds that were taking minutes.  That was until I tried to drill through some bondo, ground down the tip of two brand new drill bits to uselessness.  Maybe it was three.

Today I also formed and installed another new mudflap.  Pondering if I should replace another.  The only issue is the one in place now is short, I have to run a rivet through the folded over lip of the electronics tray and some bondo, By making a new longer mud flap i can go through just one layer of metal.

I also drilled and ground out a path for the headlight wires.  This little 90 degree head is well worth the price.  And Nancy is great to help me get a 10 dollar discount on the tool.

Monday, December 22, 2014

installing rivets

Saturday I installed my first rivet, two actually.  It was a challenge since the gun I had was not meant for such a small shank.  Sunday I bought a new rivet gun that would work for small rivets.  I installed 9 rivets so far but now my drill bit is dull and not drilling through the mudflap flashing.

As expected, complaining about something on the internet fixed it.  Along with drilling out the other rivets on the part, drilling it with a backer board, and reinstalling it.

The last mud flap I choose to make a new one, the old one was the first one made and did not have enough material to attach to center tray.  New one fits great.  But it will still be a challenge to drill the holes and mount.  Wish I had a right angle drill that was small.... er... google says dremel sells one... and that Lowes has them in stock.  It is time for a tool run.

The girls and I did a run.  Well it was cheaper at Home Depot, but non in stock.  So a generic version was purchased from Menards.  Reviews of the Milescraft is 3.5 stars, dremel is 4.5 stars.





Wednesday, December 17, 2014

amazon delivery

Today the rivets for the mud flaps and the shrink tube arrived.

I also did the bidding of Nancy and threw together a "roller skate" to hold the SBT oak tops and the big batteries on wheels so I can tuck it in a corner of a shop, it is ugly but it works.  The rest of the day was spent sleeping or resting the flu going through our house and while I am not loosing anything I am wasted, and did not work today.



Sunday, December 07, 2014

electrical work

This weekend I sorted my wire by size, this jumble of three boxes of wires was just that a jumble of store bought and rescued from past projects.  I was looking for enough 18 -22 gauge to wire up the SBT.  I found 20 feet of 4 conductor 18 gauge that will work perfectly.


I also looked for and found a momentary switch for the enable test button in my collection.  What I do not have is shrink tubing.   Also before I wire it up I should mount the mud flaps.  I do not have rivets for this thin of metal.

I did drill the hole for running the headlight wires back to the center box where it will hook up to Robb's new control box he is working on.

Next task is to drill the hole for the enable test switch.  That will be fun since my drill is longer than area I have to fit in.

The electrical plan has been drawn up many times.  The three speed wires and one of the direction wires is going to a 4 pole three position switch mounted under the side of the machine.  This switch will decide between onboard, teather, and radio control.  Onboard and teather are going to be simple systems, speed and direction only.  The radio control will also have the complexity of headlight, horn, voltmeter, amp meter, and speedometer.  Though I am going to hide my current odometer inside the machine.  

There is a risk of someone changing control source to onboard and having the machine take off.  It is not supposed to do that per the design of the control board but it has happened this summer with the current setup, hence our use of the enable test button.  Not sure if  I can find a robust system to drop out the enable when the control is changed but not when the machine is jolted around.